| Video |
| Maximum data rate |
10.2 Gbps (3.4 Gbps per color) |
| Maximum pixel clock |
300 MHz |
| Resolution range |
Up to 2560x1600* @ 60 Hz or
4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(* reduced blanking) |
| Color bit depth |
8, 10, or 12 bits — subject to the maximum data rate limit |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI, HDCP 1.1, CEA-861E |
| |
| Video input — transmitter |
| Number/signal type |
1 single link HDMI (or DVI-D*) |
| Connectors |
1 female HDMI type A |
| |
| Interconnection between transmitter and receiver |
| Connectors |
1 female RJ-45 per unit |
| Termination standard |
TIA/EIA T568B |
| Signal transmission distance |
|
| 1080p @ 60 Hz |
Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
| 2560x1600 @ 60 Hz |
Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
| 4K/UHD @ 30Hz and 60 Hz |
Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable |
| Cable requirements |
Solid conductor, 24 AWG or better |
| Cable recommendations |
400 MHz bandwidth, STP (shielded twisted pair) |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
| |
| Video output — receiver |
| Number/signal type |
1 single link HDMI (or DVI-D*) |
| Connectors |
1 female HDMI type A |
| |
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output +6 dB |
| Frequency response |
20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise |
0.03% @ 20 Hz to 20 kHz at maximum output |
| S/N |
>90 dB, at maximum output (15 dBu), balanced (unweighted) |
| Stereo channel separation |
>80 dB @ 1 kHz to 20 kHz |
| |
| Audio input |
| Number/signal type |
1 PC level stereo, unbalanced |
| NOTE |
Analog audio is not embedded onto the digital video signal. Embedded digital audio is not de-embedded from the digital video signal. |
|
| Connectors |
(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) |
| Impedance |
>10k ohms, DC coupled |
| Nominal level |
-10 dBV (316 mVrms) |
| Maximum level |
+7 dBV (unbalanced) |
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
| |
| Audio output |
| Number/signal type |
1 stereo (2 channel), balanced/unbalanced |
| Connectors |
(1) 3.5 mm captive screw connector, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Gain error |
±0.1 dB channel to channel |
| Maximum level (600 ohm) |
>+11 dBu, balanced |
| |
| Control/remote — external device (pass-through, unidirectional or bidirectional) |
| Serial control port input/output |
|
| Transmitter |
RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port) |
| Receiver |
1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output/input |
|
| Transmitter |
1 set of proprietary signals on a female RJ-45 jack |
| Receiver |
RS-232 via a 3.5 mm, 3 pole captive screw connector |
| Baud rates |
Up to 115200 baud |
| Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| Serial control pin configuration |
1 = Tx, 2 = Rx, 3 = Gnd |
| IR control port |
(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
| IR control pin configuration |
3 = Gnd, 4 = IR Tx, 5 = IR Rx |
| |
| General |
| Power supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power consumption |
|
| Transmitter |
|
| Device |
2.5 watts, 12 VDC |
| Device and power supply |
3.4 watts, 100-240 VAC, 50-60 Hz |
| Receiver |
|
| Device |
4.2 watts, 12 VDC |
| Device and power supply |
5.8 watts, 100-240 VAC, 50-60 Hz |
| NOTE |
Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, no vents |
| Thermal dissipation |
|
| Transmitter |
|
| Device |
7.4 BTU/hr |
| Device and power supply |
10.4 BTU/hr |
| Receiver |
|
| Device |
13.0 BTU/hr |
| Device and power supply |
18.7 BTU/hr |
| Mounting |
| Rack mount |
Yes, with optional 1U high rack shelf |
| Furniture mount |
Yes, with optional under-desk mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
|
| Transmitter |
1.0" H x 4.3" W x 3.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.) |
| Receiver |
1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight |
|
| Transmitter |
0.5 lbs (0.3 kg) |
| Receiver |
1.0 lb (0.5 kg) |
| Shipping weight |
3 lbs (2 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
|
| Safety |
CE, c-UL, UL
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply. |
| EMI/EMC |
CE**, C-tick, FCC Class A**, ICES, VCCI, KCC |
| NOTE |
**CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable. |
|
|
Warranty
|
3 years parts and labor
|
